How Fiber Optics Work

By: Craig Freudenrich, Ph.D. & Chris Pollette  | 
connection with dynamic fibre optic light trail
Fiber-optic lines have revolutionized long-distance phone calls, cable TV and the Internet. John Rensten/Getty Images

You hear about fiber-optic cables whenever people talk about the telephone system, the cable TV system or the internet. Fiber optics could be described as the science of transmitting data, voice and images by the passage of light through thin fibers, according to Encyclopedia Brittanica.

Fiber-optic lines are strands of optically pure glass as thin as a human hair that carry digital information over long distances. They are also used in medical imaging and mechanical engineering inspection. They have virtually replaced the older technology of copper wires in telecommunications.

Advertisement

In this article, we will show you how these tiny strands of glass transmit light and the fascinating way that these strands are made.

What Are Fiber Optics?

The structure of a typical single-mode fiber
The structure of a typical single-mode fiber: 1: core, 2: cladding, 3: buffer, 4: jacket.
Bob Mellish/Wikipedia

Fiber optics (optical fibers) are long, thin strands of very pure glass about the diameter of a human hair. They are arranged in bundles called optical cables and used to transmit light signals over long distances.

If you look closely at a single optical fiber, you will see that it has the following parts:

Advertisement

  • core - thin center of the fiber where the light travels
  • cladding - outer optical material surrounding the core that reflects the light back into the core
  • buffer - a protective plastic coating applied directly to the optical fiber
  • jacket - protective outer layer of the cable that protects the fiber from damage and moisture

Hundreds or thousands of these optical fibers are arranged in bundles in optical cables.

Optical fibers come in two types:

  1. single-mode fibers
  2. multi-mode fibers

Single-mode fibers have small cores (about 3.5 x 10-4 inches or 9 microns in diameter) and transmit infrared laser light (wavelength = 1,300 to 1,550 nanometers or nm). Multi-mode fibers have larger cores (about 2.5 x 10-3 inches or 62.5 microns in diameter) and transmit infrared light (wavelength = 850 to 1,300 nm) from light-emitting diodes (LEDs).

Some optical fibers can be made from plastic. These fibers have a large core (0.04 inches or 1 millimeter diameter) and can be used with silicon chips. Glass fiber doesn't work well with silicon and is costly to adapt.

Let's look at how an optical fiber works.

How Does an Optical Fiber Transmit Light?

fiber optics light signal
Diagram of total internal reflection in an optical fiber Online2Design.com/HowStuffWorks

Suppose you want to shine a flashlight beam down a long, straight hallway. Just point the beam straight down the hallway — light travels in straight lines, so it is no problem. What if the hallway has a bend in it? You could place a mirror at the bend to reflect the light beam around the corner. What if the hallway is very winding with multiple bends? You might line the walls with mirrors and angle the beam so that it bounces from side-to-side all along the hallway. This is exactly what happens in an optical fiber.

The light in a fiber-optic cable travels through the core (hallway) by constantly bouncing from the cladding (mirror-lined walls), a principle called total internal reflection. Because the cladding does not absorb any light from the core, the light wave can travel great distances.

Advertisement

However, some of the signal within the fiber is lost as it travels longer distances. The extent that the signal degrades depends on the purity of the glass, the number of bends in the fiber or splices that connect sections of fiber and the wavelength of the transmitted light.

For example, with multimode fiber, diameters of 850 nm = 3 dB/km; 1,300 nm = 1 dB/km. For single mode cable, 1,310 nm = 0.5 dB/km; 1,550 nm = 0.4 dB/km).

A Fiber-Optic Relay System

To understand how optical fibers are used in communications systems, let's look at an example from a World War II movie or documentary where two naval ships in a fleet need to communicate with each other while maintaining radio silence or on stormy seas. One ship pulls up alongside the other. The captain of one ship sends a message to a sailor on deck. The sailor translates the message into Morse code (dots and dashes) and uses a signal light (floodlight with a venetian blind type shutter on it) to send the message to the other ship. A sailor on the deck of the other ship sees the Morse code message, decodes it into English and sends the message up to the captain.

Now, imagine doing this when the ships are on either side of the ocean separated by thousands of miles and you have a fiber-optic communication system in place between the two ships. Fiber-optic relay systems consist of the following:

Advertisement

  • transmitter - produces and encodes the light signals
  • optical fiber - conducts the light signals over a distance
  • optical regenerator - may be necessary to boost the light signal (for long distances)
  • optical receiver - receives and decodes the light signals

Transmitter

The transmitter is like the sailor on the deck of the sending ship. It receives and directs the optical device to turn the light "on" and "off" in the correct sequence, thereby generating a light signal.

The transmitter is physically close to the optical fiber and may even have a lens to focus the light into the fiber. Lasers have more power than LEDs, but vary more with changes in temperature and are more expensive. The most common wavelengths of light signals are 850 nm, 1,300 nm and 1,550 nm (infrared, non-visible portions of the spectrum).

Optical Regenerator

As mentioned above, some signal loss occurs when the light is transmitted through the fiber, especially over long distances such as with undersea cables. Therefore, one or more optical regenerators is spliced along the cable to boost the degraded light signals.

An optical regenerator consists of optical fibers with a special coating (doping). The doped portion is "pumped" with a laser. When the degraded signal comes into the doped coating, the energy from the laser allows the doped molecules to become lasers themselves. The doped molecules then emit a new, stronger light signal with the same characteristics as the incoming weak light signal. Basically, the regenerator is a laser amplifier for the incoming signal.

Optical Receiver

The optical receiver is like the sailor on the deck of the receiving ship. It takes the incoming digital light signals, decodes them and sends the electrical signal to the other user's computer, TV or telephone (receiving ship's captain). The receiver uses a photocell or photodiode to detect the light.

Advantages of Fiber Optics

Why are fiber-optic systems revolutionizing telecommunications? Compared to conventional metal wire (copper wire), optical fibers:

Are less expensive. Fiber-optic cable is more expensive than copper wire, but it also requires less maintenance. In the long run it saves you and your internet provider money.

Advertisement

Are thinner. Optical fibers can be drawn to smaller diameters than copper wire.

Have higher carrying capacity. Because optical fibers are thinner than copper wires, more fibers can be bundled into a given-diameter cable than copper wires. This allows more phone lines to go over the same cable or more channels to come through the cable into your cable TV box.

Have less signal degradation. The loss of signal in optical fiber is less than in copper wire.

Have no interference from light signals. Unlike electrical signals in copper wires, light signals from one fiber do not interfere with those of other fibers in the same cable. This means clearer phone conversations or TV reception.

Have lower power. Because signals in optical fibers degrade less, lower-power transmitters can be used instead of the high-voltage electrical transmitters needed for copper wires. Again, this saves you and your provider money.

Have digital signals. Optical fibers are ideally suited for carrying digital information, which is especially useful in computer networks.

Are non-flammable. Because no electricity is passed through optical fibers, it does not create heat, reducing the risk of fire.

Are lightweight. An optical cable weighs less than a comparable copper-wire cable (4 pounds or 2 kilograms per 1,000 feet or 305 meters, versus 39 pounds or 18 kilograms per 1,000 feet). Fiber-optic cables take up less space in the ground, too.

Are flexible. Because fiber optics are so flexible and can transmit and receive light, they are used in many flexible digital cameras for the following purposes:

  • medical imaging - in bronchoscopes, endoscopes, laparoscopes
  • mechanical imaging - inspecting mechanical welds in pipes and engines (in airplanes, rockets, space shuttles, cars)
  • plumbing - to inspect sewer lines

Because of these advantages, you see fiber optics in many industries, most notably telecommunications and computer networks. For example, if you phoned Europe on a landline from the United States (or vice versa) and the signal bounces off a communications satellite, you'd often hear an echo on the line. But with transatlantic fiber-optic cables, you have a direct connection with no echoes.

How Are Optical Fibers Made?

MCVD process for making the preform blank
The glass for the preform is made by a process called modified chemical vapor deposition(MCVD). Fibercore Ltd./Outline2Design.com/HowStuffWorks

Now that we know how fiber-optic systems work and why they are useful, how do they make them? Optical fibers are made of extremely pure optical glass. We think of a glass window as transparent, but the thicker the glass gets, the less transparent it becomes due to impurities in the glass. However, the glass in an optical fiber has far fewer impurities than windowpane glass.

Making optical fibers requires the following steps:

Advertisement

  • making a preform glass cylinder
  • drawing the fibers from the preform
  • testing the fibers

Making the Preform Blank

The glass for the preform is made by a process called modified chemical vapor deposition (MCVD).

In MCVD, oxygen is bubbled through solutions of silicon tetrachloride (SiCl4), germanium tetrachloride (GeCl4), phosphorus trichloride (PoCl3) and/or other chemicals. The precise mixture governs the various physical and optical properties (index of refraction, coefficient of expansion, melting point, etc.). The gas vapors are then conducted to the inside of a synthetic silica or quartz tube (cladding) in a special lathe. As the lathe turns, a torch is moved up and down the outside of the tube. The extreme heat from the torch causes two things to happen:

  • The silicon and germanium react with oxygen, forming silicon dioxide (SiO2) and germanium dioxide (GeO2).
  • The silicon dioxide and germanium dioxide deposit on the inside of the tube and fuse together to form glass.

The lathe turns continuously to make an even coating and consistent blank. The purity of the glass is maintained by using corrosion-resistant plastic in the gas delivery system (valve blocks, pipes, seals) and by precisely controlling the flow and composition of the mixture. The process of making the preform blank is highly automated and takes several hours. After the preform blank cools, it is tested for quality control (index of refraction).

Drawing Fibers from the Preform Blank

Diagram of a fiber drawing tower used to draw optical glass fibers from a preform blank
Diagram of a fiber drawing tower used to draw optical glass fibers from a preform blank.
Outline2Design/HowStuffWorks

Once the preform blank has been tested, it gets loaded into a fiber drawing tower.

The blank gets lowered into a graphite furnace (3,452 to 3,992 degrees Fahrenheit or 1,900 to 2,200 degrees Celsius) and the tip gets melted until a molten glob falls down by gravity. As it drops, it cools and forms a thread.

The operator threads the strand through a series of coating cups (buffer coatings) and ultraviolet light curing ovens onto a tractor-controlled spool. The tractor mechanism slowly pulls the fiber from the heated preform blank and is precisely controlled by using a laser micrometer to measure the diameter of the fiber and feed the information back to the tractor mechanism.

Fibers are pulled from the blank at a rate of up to 66 ft/s (20 m/s) and the finished product is wound onto the spool. It is not uncommon for individual spools to contain miles or kilometers of optical fiber.

Testing the Finished Optical Fiber

The finished optical fiber is tested for the following:

  • Tensile strength. Must withstand 100,000 lb/in2 or more
  • Refractive index profile. Determine numerical aperture as well as screen for optical defects
  • Fiber geometry. Core diameter, cladding dimensions and coating diameter are uniform
  • Attenuation. Determine the extent that light signals of various wavelengths degrade over distance
  • Information carrying capacity (bandwidth). Number of signals that can be carried at one time (multi-mode fibers)
  • Chromatic dispersion. Spread of various wavelengths of light through the core (important for bandwidth)
  • Operating temperature/humidity range
  • Temperature dependence of attenuation
  • Ability to conduct light underwater. Important for undersea cables

Once the fibers have passed the quality control, they are sold to telephone companies, cable companies and network providers. Most companies have replaced their old copper-wire-based systems with new fiber-optic-based systems to improve speed, capacity and clarity.

Physics of Total Internal Reflection

Total internal reflection in an optical fiber
Total internal reflection in an optical fiber Online2Design.com/HowStuffWorks

When light passes from a medium with one index of refraction (m1) to another medium with a lower index of refraction (m2), it bends or refracts away from an imaginary line perpendicular to the surface (normal line). As the angle of the beam through m1 becomes greater with respect to the normal line, the refracted light through m2 bends further away from the line.

At one particular angle (critical angle), the refracted light will not go into m2, but instead will travel along the surface between the two media (sine [critical angle] = n2/n1 where n1 and n2 are the indices of refraction [n1 is greater than n2]). If the beam through m1 is greater than the critical angle, then the refracted beam will be reflected entirely back into m1 (total internal reflection), even though m2 may be transparent!

Advertisement

In physics, the critical angle is described with respect to the normal line. In fiber optics, the critical angle is described with respect to the parallel axis running down the middle of the fiber. Therefore, the fiber-optic critical angle = (90 degrees - physics critical angle).

In an optical fiber, the light travels through the core (m1, high index of refraction) by constantly reflecting from the cladding (m2, lower index of refraction) because the angle of the light is always greater than the critical angle. Light reflects from the cladding no matter what angle the fiber itself gets bent at, even if it's a full circle!